12-1822

ZPA 3 - Automatic Auto-Ignition Tester

with Heated Sample-Feeder

Liquids: EN 14 522 - CEI 79-4 - NF T20-037 (DIN 51 794 requires alternative firmware)

with further accessories for:
Solids: NF T20-036 - 79/831/EWG

Consisting of:

Furnace with safety cage:
adjustable up to +650 °C, with holder for temperature probe, indicator and sample syringe

Metal insert:
stainless steel with an additional fixture for temperature probe

Test insert:
complete with two-part (non-asbestos) insulation ring, ignition flask (200 ml) and thermocouple

Calibration block:
for automatic thermocouple testing, adjustment and calibration

Control unit:
with a three-step program for pre-tests, main tests and automatic calibration of thermocouples. Connections for compressed air (valve controlled air purge) and recorder to register temperature curves. Permanent display of furnace and sample temperatures as well as information about test run, heating and program sequence.

Automatic Sample feeding device:
with drop counting controlled by photocells, equipped with a peristaltic pump (VlTON®-sampling hose). Further equipped with a heating device (required by samples of solid consistence at ambient temperatures) to heat up the sample by an air chamber. Due to special designed pump and tubing, the temperature will remain unchanged all the way up into the drip-tip of the feeder arm. Adjustable temperature range between ambient and +95 °C.

Printer:
documentation of each completed ignition attempt with sample no., program segment, pre-selected temperature, sample volume, ignition delay, flash intensity, code and program time lapse.
For sample temperature curves the printer can be replaced by a single-line recorder (not included).

Supplied with:
1 ignition flask
1 cover for test insert
3 insulation ring for cover
1 ignition point indicator
1 temperature probe Pt-100
1 thermocouple for test flask

Note: Alternative firmware for DIN 51794 upon request.
A solid heating program is included but the required accessories are on separate order.

Power supply : 230 V, 50/60 Hz, 1200 W

12-1823

ZPA 3 - Automatic Auto-Ignition Tester

with Heated Sample-Feeder

Like 12-1822 but:
Power supply : 115 V, 50/60 Hz

12-1800

ZPA 3 - Semi-Automatic Auto-Ignition Tester

without Sample-Feeder

Depending on the components only suitable for:
Liquids: EN 14 522 - CEI 79-4 - NF T20-037 (DIN 51 794 requires alternative firmware)

Like 12-1822 but:
with sample syringe instead of Automatic Sample Feding Device

Power supply : 230 V, 50/60 Hz, 1200 W

12-1801

ZPA 3 - Semi-Automatic Auto-Ignition Tester

without Sample-Feeder

Like 12-1800 but:
Power supply : 115 V, 50/60 Hz

12-0838

Solid Conversion Set

79/831/EWG
Consisting of:
1 thermocouple (NiCr-Ni)
10 baskets

12-0819

Syringe, 1 ml

for sample introduction

Note! Required for sample introduction without automatic sample feeding device.

12-0816

Ignition Flask, 200 ml, made of glass (Erlenmeyer flask)

12-0850

Furnace with safety case

12-0854

Metal Insert for furnace, made of stainless steel

12-0855

Air Purging Device

12-0858

Cover for test insert

12-0859

Insulation Ring for cover

12-0863

Ignition Point Indicator

12-0864

Temperature Probe Pt-100

to measure the furnace temperature

12-0870

Baskets for testing solids (cube)

made of metal, pack of 10

12-0871

Thermocouple for test flask (NiCr-Ni)

with protective tubes to measure flask temperature

12-0872

Thermocouple for solids (NiCr-Ni)

12-0882

Sampling Hoses (VITON®), type D, pack of 10

12-0883

Sampling Hoses (EPDM/PP), pack of 10

resistant against acetone

12-0829

Hose Connection for gas conversion set, 1 m

12-0832

Hand Pump for gas conversion set, 200 ml, made of glass

Minimum equipment:

1x 12-1822, 1x 12-1838 or 12-0831

Spares (approx. 1 year):

12-0816, 12-0870, 12-0878

Additional requirements: