10-0350

DD 3 / 100 - Semi-Automatic Ductilometer

(test length up to 100 cm)

Elongation-Tests:
ASTM D 113 - AASHTO T51 - JIS K2207
(DIN 52013, IP 32, NF T66-006)

With further accessories suitable for:

Recovery-Tests:
ASTM D 6084 - IP 516 - EN 13 398
(ASTM D 5892, ASTM P 226, DIN V 52021-1)

Features:
• variable traction speed up to 140 mm/min.
• constancy of speed and temperature at minor bath motion is
  better than demanded by the standards
• without cooling coils, therefore easy to clean

Bath: for 3 simultaneous tests, made of stainless steel, double-walled and full insulated, closed cycle cooling system, circulation pump to be switched off, bath illumination and acrylic bath cover.

Control Unit: with microprocessor, membrane keypad, RS 232-interface.
Digital display (LCD) of: program, traction speed, distance

2 Programs:
- Semi-Automatic Elongation
- Semi-Automatic Elastic Recovery for polymer modified bitumen
  (in accordance with ASTM D 6084, EN 13398 and other methods)

Serial Printer: for single sheet & continuous paper (incl. data transmission cable) for printouts of 3 test points with following parameters: program, traction speed, distance

Supplied with:
with 3 molds (acc. ASTM D 113, if not ordered otherwise), 3 mold-holders,
2 corrosion protection specimen, 2 contrast inlays, 2 distance pieces
3 thermometers ASTM 63C, 3 thermometer-holders

Note: External cooling device for filling the bath-jacket is required.

Power supply: 220/240 V, 50/60 Hz, EU-plug

10-0351

DD 3 / 100 - Semi-Automatic Ductilometer

(test length up to 100 cm)

Like 10-0350 but:
Power supply: 115 V, 60 Hz, US-plug

10-0354

DD 3 / 150 - Semi-Automatic Ductilometer

(test length up to 150 cm)

Elongation-Tests:
ASTM D 113 - AASHTO T51 - JIS K2207
(DIN 52013, IP 32, NF T66-006)

With further accessories suitable for:

Recovery-Tests:
ASTM D 6084 - IP 516 - EN 13 398
(ASTM D 5892, ASTM P 226, DIN V 52021-1)

Like 10-0350 but:
with 3 contrast inlays , 3 distance pieces and differing technical data.

Power supply: 220/240 V, 50/60 Hz, EU-plug

10-0355

DD 3 / 150 - Semi-Automatic Ductilometer

(test length up to 150 cm)

Like 10-0354 but:
Power supply: 115 V, 60 Hz, US-plug

10-0380

Circulator (-40/+200) with accessories

For heating & cooling of instruments without circulation pump
(e.g. bath jacket filling device) and / or for tempering applications directly in the bath.

Consisting of:
Cooler with stainless steel bath. Thermostat with digital display, splash-proof keypad, heater, pump, RS232/RS485-interface, Pt-100-socket, programmer, over/under-temperature & low-level protection, adjustable pump-pressure, proportional cooling control.

Supplied with: 1 bath cover, 1 drain tap, 1 junction line for temperature probe (10-0382)

Note: Insulated hose-set is recommended.

Technical Data:
Working range: -40 to +200 °C (at +5 to +40 °C ambient temp.)
Display / Resolution: VFD & LCD / 0. 01 or 0.01 °C
Control: Integrated Programmer
Heater capacity: 2000 W
Cooling capacity: 680 W at +20 °C
Pump-Pressure capacity: 22-26 l/min, 0.4-0.7 bar (5.8-10.2 psi)
Pump-Suction capacity: 22-26 l/min, 0.2-0.4 bar (2.9-5.8 psi)
Bath opening: 23 x 14 x 20 cm (WxDxH)
Safety class / Bath fluid: 3 / FL (Flammable Liquids possible)
Volume: 16 l
Sockets for: Pt-100, solenoid valve
Dimensions / Weight: 37 x 46 x 71 cm (WxDxH), 49 kg
Power supply: 230 V, 50 Hz, 13 A, EU-plug

10-0381

Circulator (-40/+200) with accessories

Like 10-0380 but:
Power supply: 230 V, 60 Hz (115 V not available)

25-0228

Hose-Set (Ø 8 mm)

insulated, 2 x 2 m, incl. fittings

21-0697

Digital Stop Watch

Consisting of:
7-digit LC display, max. 10 hours countdown with 1/100 sec. precision, Lithium battery
• quartz-controlled
• water resistant
• memory function
• calendar

10-0335

Mold (4-piece), brass

for bitumen briquettes preparation acc. to:
ASTM D 113 (2007) - AASHTO T 51
Note: the (year of issue) refers to latest changes in molds only!

10-1337

Mold (4-piece), brass

for bitumen briquettes preparation acc. to:
ASTM D 6084 (2006) - AASHTO T300
Note: the (year of issue) refers to latest changes in molds only!

10-0332

Mold (4-piece), brass

for bitumen briquettes preparation acc. to:
EN 13 398 (2003) - IP 516 - DIN 52 013 (2007)
Note: the (year of issue) refers to latest changes in molds only!

10-1336

Mold (4-piece), brass

for bitumen briquettes preparation acc. to:
EN 13 589 (2003) - IP 520 - DIN EN 13 589 (2008)
EN 13 703 (2003) - IP 515
Note: the (year of issue) refers to latest changes in molds only!

10-1333

Mold Holder (fits all petrotest ductility molds)

10-0399

Calibration Set - DD

Consisting of:
1 set of precision resistor plugs,
1 certified thermometer (0 to +50 : 0.1°C),
1 thermometer holder,
1 digital stop watch,
1 tape-measure with mm-division

10-0383

Thermometer DIN 12775 - E0,1/0/50

Range: 0 to +50 : 0.1 °C
Length: 220 mm, Immersion: --, Ø 8 mm

10-0384

Thermometer DIN 12775 - E0,1/0/50

Range: 0 to +50 : 0.1 °C (officially certified)

10-0403

Rack, 80 x 25 x 42 cm (L x W x H)

to place controller and printer behind the Ductilometer

18-0403

Circulator-Bath (+20/+150)

For direct tempering in the bath and / or
for heating of small instruments without circulation pump (external tempering).

Consisting of:
Stainless steel bath with adjustable intermediate bottom and cooling-coil.
Thermostat with digital display, splash-proof keypad, heater, pump, RS232-interface, over-temperature- & low-level-protection.

Supplied with:
1 bath cover Ø 5 cm, 1 bath cover 20 x 20 cm, 1 thermometer (-2 to +105 : 0.5 °C)

Note: Requires counter-cooling for applications near ambient temperatures.
Insulated hose-set is recommended.

Technical Data:
Working range: +20 to +150 °C (at +5 to +40 °C ambient temp.)
Display / Resolution: LED / 0.01 °C
Heater capacity: 2000 W
Pump-Pressure capacity: 15 l/min, 0.32 bar (4.64 psi)
Bath opening: 20 x 20 x 25 cm (WxDxH)
Safety class / Bath fluid: 3 / FL (Flammable Liquids possible)
Volume: 20 l
Dimensions / Weight: 37.5 x 45 x 47.5 cm (WxDxH), 3.4 kg
Power supply: 230 V, 50 Hz, EU-plug

18-0402

Circulator-Bath (+20/+150)

Like 18-0403 but:
Heater capacity: 1000 W
Power supply: 115 V, 60 Hz

11-0181

Hose, silicon (Ø 8 mm, 8 m)

10-0377

Contrast Inlay (6 x 170 x 550 mm) pack of 1

10-0406

Corrosion Protection Specimen (200 x 100 mm) pack of 2

10-0385

Thermometer ASTM 63C

Range: -8 to +32 : 0.1 °C
Length: 379 mm, Immersion: total, Ø 7.5 mm

10-0386

Thermometer ASTM 63C

Range: -8 to +32 : 0.1 °C (officially certified)

Minimum equipment:

1 each of DD 3, 10-0380, 25-0228, 21-0697

Spares (approx. 1 year):

3x molds, 1x thermometer, 1x 10-0406

Additional requirements: