11-0542

ADU 4 - Automatic Distillation Unit with Fire-Extinguisher

Petroleum Products at Atmospheric Pressure: ASTM D 86 -
IP 123 - ISO 3405 (DIN 51751 - NF M07-002) - JIS K2254

With further accessories suitable for:
Industrial Aromatic Hydrocarbons: ASTM D 850
Volatile Organic Liquids: ASTM D 1078 - IP 195

Consisting of:
Heating cabinet with built-in fire-extinguisher, microprocessor controlled electric heater (1200 W), temperature probe and jack for height adjustment of flask. Condenser tube with water jacket for tempering by external thermostatic circulator. Recovery cabinet with light barrier detection.
High-grade stainless steel housing with two-color powder coating, digital display, keys and RS232 interface.

Supplied with:
1 ADUcon-software to allow a computer-supported operation
1 ADUpro-software as PC extension module with additional functions:
   - Heat-Parameter Optimizer (If necessary, this software recommends more adequate heat-
     parameters for the next test run automatically.
   - Pre-selected Temperature-Spread-Sheet (additionally to the Volume-Spread-Sheet the selection
     of nearly all temperature-values and the corresponding volume recovered is possible)
   - Support of solvent distillation acc. ASTM D 850 & D 1078
     (with a preset parameter library for different solvents)
   - Connection and simultaneous run of up to 6 ADU-units with 1 PC
     (if not enough RS232-ports available, we recommend a USB-Hub)
     Note: Each ADU-unit requires a separate ADUpro-Software installation.
1 glassware set according ASTM D 86 (Group 1-4)
   (1 flask 125 ml, 2 glass-ceramic plates with hole 1x Ø 38 & 1x Ø 50 mm)
1 PTFE-stopper 19/26 to hold the temperature probe
1 stopper to connect flask condenser tube
1 graduated cylinder 100 ml with metal base
1 drip tongue
1 cleaning coil for the condenser tube
1 test sample (300 ml bottle)
1 insulating hose set for cooler connection
1 connection set
  (data cable for cooler, 0-modem cable, RS232-adapter, USB-converter)

Power supply: 230 V, 50 Hz

11-0543

ADU 4 - Automatic Distillation Unit with Fire-Extinguisher

Like 11-0542 but:
Power supply: 115 V, 60 Hz

11-1542

ADU 4 - Automatic Distillation Unit with Dry-Point Detection & Fire-Extinguisher

Petroleum Products at Atmospheric Pressure: ASTM D 86 -
IP 123 - ISO 3405 (DIN 51751 - NF M07-002) - JIS K2254

With further accessories suitable for:
Industrial Aromatic Hydrocarbons: ASTM D 850
Volatile Organic Liquids: ASTM D 1078 - IP 195

Like 11-0542 but: A sensor for dry-point detection must be ordered separately (acc. to flask size). Further it requires external CO₂ or N₂ supply between 6 and 12 bar.

Power supply: 230 V, 50 Hz

11-1543

ADU 4 - Automatic Distillation Unit with Dry-Point Detection & Fire-Extinguisher

Like 11-1542 but:
Power supply: 115 V, 60 Hz

11-0546

Glassware Set (Group 0-4)

ASTM D 86 - ISO 3405 - IP 123 - JIS K2254
Consisting of:
1 flask 100 ml, neck 19/26 (group 0)
1 glass-ceramic plate with hole Ø 32 mm (group 0)
1 flask 125 ml, neck 19/26 (group 1-4)
1 glass-ceramic plate with hole Ø 38 mm (group 1-4)
1 glass-ceramic plate with hole Ø 50 mm (group 1-4)

11-0536

Glassware Set (Group 1-4)

ASTM D 86 - ISO 3405 - IP 123 - JIS K2254
Consisting of:
1 flask 125 ml, neck 19/26 (group 1-4)
1 glass-ceramic plate with hole Ø 38 mm (group 1-4)
1 glass-ceramic plate with hole Ø 50 mm (group 1-4)

11-0524

Distillation Flask, 125 ml, ground socket (NS 19/26)

with thermometer immersion-mark, side pipe Ø 7 mm,
quartz glass (for temperatures above 370 °C)
(ASTM E133/B, Engler-shape)

11-0588

Dry-Point Sensor fits 100/125 ml flask

11-0547

Glassware Set (Solvents)

ASTM D 850 - ASTM D 1078 - IP 195
Consisting of:
1 flask 200 ml, neck 19/26
1 glass-ceramic plate with hole Ø 25 mm
1 glass-ceramic plate with hole Ø 32 mm
1 glass-ceramic plate with hole Ø 38 mm
1 glass-ceramic plate with hole Ø 50 mm

11-0596

Cylinder HR, 100 ml, borosilicate glass, graduated

(complete with tube, metal base and O-rings)

11-0587

Dry-Point Sensor fits 200 ml flask

11-0575

Anti-Dazzle Screen

(for dazzling-free dry-point observations)

11-0571

Calibration Set - ADU4 Volume-Detection

Consisting of:
1 Burette (50:0.1 ml)
1 Burette-holder set

11-0582

Calibration Set - ADU4/4+ Temperature

Consisting of:
1 Calibration-Resistor-Set
1 Thermometer IP 39C (official certified)

11-0590

Reference Liquid - Distillation of Mineral Oil Products
(Boiling Characteristics)

ASTM D 86 - ISO 3405

Initial Boiling Point: approx. 160°C,
Final Boiling Point: approx. 360°C
Data evaluated by International Industrial Round Robin Test.

Aluminum bottle / content 255 ml.

11-0591

Reference Liquid - Distillation of Gasoline (Unleaded)

ASTM D 86

Certified Value: approx. 30 °C - 184 °C, 250 ml

11-0593

Reference Liquid - Distillation of Diesel

ASTM D 86

Certified Value: approx. 163 °C to 362 °C, 250 ml

11-0545

Boiling-Stones, pack of 20 g

against the boiling retardation
Note: Do not use with dry-point detection.

11-0597

O-Ring Set (Chemraz), solvent resistant

(used for condenser tube stopper and flask-neck)

25-0803

Computer with Monitor & Graphic-Printer

allows to connect up to 6 instruments
(detailed specifications upon request)
Power supply: 230 V, 50 Hz

11-0598

USB-Hub Device (4-ports) with power supply (EU-plug)

to connect 4 instruments by USB 2.0 to one PC USB-port, (Verified for petrotest® units)

11-0594

USB-Hub Device (4-ports) with power supply (US-plug-adapter)

25-0282

Impact Printer (mono)

for single sheets & continuous paper
to record data like test results, duration of test, etc. (instead of a PC)

Supplied with: 2 data cables (9-pin 25-0304, USB 25-0918), 1 ink ribbon (black)

Technical Data:
Line spacing: 80 characters per line (10 cpi)
Page size : 257 x 364 mm (sheet), 254 x 558.8 mm (roll)
Ports: serial (9-pin), USB (1.1)
Dimensions: 37 x 28 x 16 cm (WxDxH)
Weight: 5 kg
Power supply: 220/240 V, 50/60 Hz

25-0283

Impact Printer

Like 25-0282 but:
Power supply: 110/130 V, 50/60 Hz

25-0240

Circulator (-28/+200)

For heating & cooling of instruments without circulation pump
and / or for tempering applications directly in the bath.

Consisting of:
Cooler with stainless steel bath.Thermostat with digital display, splash-proof keypad, integrated heater, pump, RS232-interface, over/under-temperature & low-level protection, adjustable pump-pressure, cooling control.

Supplied with: 1 bath cover, 1 drain tap

Note: Insulated hose-set is recommended.

Technical Data:
Working range: -28 to +200 °C (at +5 to +40 °C ambient temp.)
Display / Resolution: LED / 0.01 or 0.1 °C
Heater capacity: 2000 W
Cooling capacity: 260 W at +20 °C
Pump-Pressure capacity: 11-16 l/min, , 0.23-0.45 bar (3.3-6.5 psi)
Bath opening: 12 x 14 x 14 cm (WxDxH)
Safety class / Bath fluid: 3 / FL (Flammable Liquids possible)
Volume: 4.5 l
Sockets for: hose (Ø 8 / 10 mm), solenoid valve
Dimensions / Weight: 23 x 42 x 61 cm (WxDxH), 31 kg
Power supply: 230 V, 50/60 Hz, 12 A, EU-plug

25-0241

Circulator (-28/+200)

Like 25-0240 but:
Heater capacity: 1000 W
Power supply: 115 V, 60 Hz, US-plug

25-0242

Circulator (-35/+200)

For heating & cooling of instruments without circulation pump
and / or for tempering applications directly in the bath.

Consisting of:
Cooler with stainless steel bath. Thermostat with digital display, splash-proof keypad, integrated heater, pump, RS232-interface, over/under-temperature & low-level protection, adjustable pump-pressure, cooling control.

Supplied with: 1 bath cover, 1 drain tap

Note: Insulated hose-set is recommended

Technical Data:
Working range: -35 to +200 °C (at +5 to +40 °C ambient temp.)
Display / Resolution: LED / 0.01 or 0.1 °C
Heater capacity: 2000 W
Cooling capacity: 450 W at +20 °C
Pump-Pressure capacity: 11-16 l/min, 0.23-0.45 bar (3.3-6.5 psi)
Bath opening: 18 x 12 x 15 cm (WxDxH)
Safety class / Bath fluid: 3 / FL (Flammable Liquids possible)
Volume: 8 l
Sockets for: hose (Ø 8 / 10 mm)
Dimensions / Weight: 31 x 42 x 64 cm (WxDxH), 37 kg
Power supply: 230 V, 50 Hz, 13 A, EU-plug

25-0243

Circulator (-35/+200)

Like 25-0242 but:
Heater capacity: 1000 W
Power supply: 115 V, 60 Hz, US-plug

11-0574

Spare Parts Set - ASTM D 86 (Group 1-4)

for approx. 1 year consisting of:
10x 11-0515 (125 ml flask),
  2x 11-0554 (100 ml cylinder),
  1x 11-0558 (5 stoppers),
  1x 11-0559 (temperature probe),
  1x 11-0567 (drip tongue)

11-0514

Distillation Flask, 100 ml, ground socket (NS 19/26)

with thermometer immersion-mark, side pipe Ø 7 mm,
(ASTM E133/A, Engler-shape)

11-0515

Distillation Flask, 125 ml, ground socket (NS 19/26)

with thermometer immersion-mark, side pipe Ø 7 mm,
(ASTM E133/B, Engler-shape)

11-0524

Distillation Flask, 125 ml, ground socket (NS 19/26)

with thermometer immersion-mark, side pipe Ø 7 mm,
quartz glass (for temperatures above 370 °C)
(ASTM E133/B, Engler-shape)

11-0517

Distillation Flask, 200 ml, ground socket (NS 19/26)

with thermometer immersion-mark, side pipe Ø 7 mm,
(ASTM E133/C, Barret-shape)

11-0567

Drip Tongue

11-0554

Cylinder, 100 ml, borosilicate glass, graduated

(complete with tube, metal base and O-rings)

11-0596

Cylinder HR, 100 ml, borosilicate glass, graduated

(complete with tube, metal base and O-rings)

11-0555

Cylinder Tube, borosilicate glass, graduated

11-0556

Cylinder Metal Base, (fits 11-0555) with 3 O-rings

11-0595

Cylinder Metal Base HR (fits 11-0555)

with 3 O-rings (top one high resistant)

11-0557

O-Rings for metal base 11-0556 inside, pack of 10

11-0573

O-Rings for metal base 11-0556 outside, pack of 10

11-0572

Dismantling Device for cylinder metal base

11-0135

Support Board, center hole Ø 25 mm (1")

glass ceramics (150 x 150 x 4 mm)

11-0136

Support Board, center hole Ø 32 mm (1 ¼")

glass ceramics (150 x 150 x 4 mm)

11-0137

Support Board, center hole Ø 38 mm (1 ½")

glass ceramics (150 x 150 x 4 mm)

11-0138

Support Board, center hole Ø 50 mm (2")

glass ceramics (150 x 150 x 4 mm)

11-0561

Electric Heater Assembly, 1200 W

(incl. 1 heater rod with & 1 w/o sensor )

11-0039

Heater Rod, 600 W, 115/230 V

without temperature sensor

11-0579

Heater Rod, 600 W, 115/230 V

with integrated temperature sensor

11-0578

Heating-Temperature Sensor (NiCr-Ni)

11-0559

Sample-Temperature Probe (Pt-100)

11-0521

Stopper, PTFE (NS 19/26 / bored Ø 6 mm) with 2 O-rings

as temperature probe support

11-0549

Cleaning Coil for condenser tube

11-0558

Stopper PEEK (Ø 12 / bored Ø 6 mm), pack of 5

with 3 O-rings, high-temperature resistant
(to connect condenser tube with distillation flask side pipe)

11-0584

O-Ring Set for stopper 11-0558

Consisting of: 1 outer- & 2 inner - O-rings

11-0564

Burette, 50:0.1 ml

11-0565

Burette-Holder

26-0037

Thermometer IP 39C

Range: -1 to +38 : 0.1 °C (officially certified)

25-0229

Hose-Set (Ø 10 mm)

insulated, 2x 2 m, incl. fittings

Minimum equipment:

1x ADU, 1x Test set, 1x Cooler

Spares (approx. 1 year):

1x Spare part set

Additional requirements:

CO₂ / N₂-supply (6 to 12 bar) for fire-extinguisher